Compare injection molding machine quotes without erasing their original basis.

INJECTION MOLDING MACHINE — SUPPLIER CLARIFICATION BRIEF

This browser-local brief lists only supplier-facing gaps recorded in the current comparison table: raw supplier entry, source unit / declared basis, and document / trial reference.
Buyer-normalized entries are intentionally excluded. Normalization is a buyer-owned comparison input, not a supplier clarification request.
A missing item is a completeness prompt only; it does not determine machine fit, compliance or supplier qualification.

=== Quote A ===
Buyer record reference: [not recorded by buyer]

[Scope / identity] Quoted machine and configured scope
- Please provide the raw supplier entry (original quoted value or wording).
- Please state the source unit / declared basis.
- Please identify the controlled document or agreed trial reference.

[Mold fit] Clamp, platen and tie-bar fit
- Please provide the raw supplier entry (original quoted value or wording).
- Please state the source unit / declared basis.
- Please identify the controlled document or agreed trial reference.

[Mold fit] Mold thickness, daylight, opening and ejection
- Please provide the raw supplier entry (original quoted value or wording).
- Please state the source unit / declared basis.
- Please identify the controlled document or agreed trial reference.

[Mold fit / site] Mold weight, support and handling access
- Please provide the raw supplier entry (original quoted value or wording).
- Please state the source unit / declared basis.
- Please identify the controlled document or agreed trial reference.

[Injection] Shot capacity and usable shot basis
- Please provide the raw supplier entry (original quoted value or wording).
- Please state the source unit / declared basis.
- Please identify the controlled document or agreed trial reference.

[Injection] Injection speed, volume rate, pressure and fill evidence
- Please provide the raw supplier entry (original quoted value or wording).
- Please state the source unit / declared basis.
- Please identify the controlled document or agreed trial reference.

[Plasticizing] Plasticizing capacity and recovery window
- Please provide the raw supplier entry (original quoted value or wording).
- Please state the source unit / declared basis.
- Please identify the controlled document or agreed trial reference.

[Energy / boundary] Energy method, included loads and denominator
- Please provide the raw supplier entry (original quoted value or wording).
- Please state the source unit / declared basis.
- Please identify the controlled document or agreed trial reference.

[Interfaces / safety] Robot, peripheral, data and safety interfaces
- Please provide the raw supplier entry (original quoted value or wording).
- Please state the source unit / declared basis.
- Please identify the controlled document or agreed trial reference.

[Utilities / auxiliaries] Power, cooling, air and auxiliary scope
- Please provide the raw supplier entry (original quoted value or wording).
- Please state the source unit / declared basis.
- Please identify the controlled document or agreed trial reference.

[Service / handover] Spares, files, training and support handover
- Please provide the raw supplier entry (original quoted value or wording).
- Please state the source unit / declared basis.
- Please identify the controlled document or agreed trial reference.

[Trial / documents] Trial configuration and acceptance evidence
- Please provide the raw supplier entry (original quoted value or wording).
- Please state the source unit / declared basis.
- Please identify the controlled document or agreed trial reference.


=== Quote B ===
Buyer record reference: [not recorded by buyer]

[Scope / identity] Quoted machine and configured scope
- Please provide the raw supplier entry (original quoted value or wording).
- Please state the source unit / declared basis.
- Please identify the controlled document or agreed trial reference.

[Mold fit] Clamp, platen and tie-bar fit
- Please provide the raw supplier entry (original quoted value or wording).
- Please state the source unit / declared basis.
- Please identify the controlled document or agreed trial reference.

[Mold fit] Mold thickness, daylight, opening and ejection
- Please provide the raw supplier entry (original quoted value or wording).
- Please state the source unit / declared basis.
- Please identify the controlled document or agreed trial reference.

[Mold fit / site] Mold weight, support and handling access
- Please provide the raw supplier entry (original quoted value or wording).
- Please state the source unit / declared basis.
- Please identify the controlled document or agreed trial reference.

[Injection] Shot capacity and usable shot basis
- Please provide the raw supplier entry (original quoted value or wording).
- Please state the source unit / declared basis.
- Please identify the controlled document or agreed trial reference.

[Injection] Injection speed, volume rate, pressure and fill evidence
- Please provide the raw supplier entry (original quoted value or wording).
- Please state the source unit / declared basis.
- Please identify the controlled document or agreed trial reference.

[Plasticizing] Plasticizing capacity and recovery window
- Please provide the raw supplier entry (original quoted value or wording).
- Please state the source unit / declared basis.
- Please identify the controlled document or agreed trial reference.

[Energy / boundary] Energy method, included loads and denominator
- Please provide the raw supplier entry (original quoted value or wording).
- Please state the source unit / declared basis.
- Please identify the controlled document or agreed trial reference.

[Interfaces / safety] Robot, peripheral, data and safety interfaces
- Please provide the raw supplier entry (original quoted value or wording).
- Please state the source unit / declared basis.
- Please identify the controlled document or agreed trial reference.

[Utilities / auxiliaries] Power, cooling, air and auxiliary scope
- Please provide the raw supplier entry (original quoted value or wording).
- Please state the source unit / declared basis.
- Please identify the controlled document or agreed trial reference.

[Service / handover] Spares, files, training and support handover
- Please provide the raw supplier entry (original quoted value or wording).
- Please state the source unit / declared basis.
- Please identify the controlled document or agreed trial reference.

[Trial / documents] Trial configuration and acceptance evidence
- Please provide the raw supplier entry (original quoted value or wording).
- Please state the source unit / declared basis.
- Please identify the controlled document or agreed trial reference.

INJECTION MOLDING MACHINE — MULTI-QUOTE SPECIFICATION RECORD

This record compares completeness and stated bases. It does not rank suppliers, determine machine fit or replace controlled files and trials.
Entries were prepared in the browser and are not submitted by this tool.

BUYER PROJECT BASIS
Part / application: [not recorded]
Resin / grade: [not recorded]
Buyer output target: [not recorded]
Mold file basis: [not recorded]
Destination / site basis: [not recorded]
Planned verification: [not recorded]

=== Quote A ===
Quote / file reference: [not recorded]

[Scope / identity] Quoted machine and configured scope
Raw supplier entry: [missing]
Source unit / basis: [missing]
Buyer-normalized entry: [pending]
Document / trial reference: [missing]
Completeness note: Raw value missing
Comparison basis: Model, injection unit, screw, clamping unit, options, auxiliaries and quote revision.
Verification boundary: Match the commercial offer to the controlled configuration list and drawings.

[Mold fit] Clamp, platen and tie-bar fit
Raw supplier entry: [missing]
Source unit / basis: [missing]
Buyer-normalized entry: [pending]
Document / trial reference: [missing]
Completeness note: Raw value missing
Comparison basis: Buyer-required clamp basis plus usable tie-bar spacing and platen area in one unit system.
Verification boundary: Check the mold drawing, projected-area/pressure basis and configured machine drawing; do not infer fit from nominal tonnage alone.

[Mold fit] Mold thickness, daylight, opening and ejection
Raw supplier entry: [missing]
Source unit / basis: [missing]
Buyer-normalized entry: [pending]
Document / trial reference: [missing]
Completeness note: Raw value missing
Comparison basis: Minimum/maximum mold thickness, opening stroke, daylight, ejector stroke/force and core requirements.
Verification boundary: Verify the installed mold stack, motion sequence and access using controlled drawings and an agreed trial.

[Mold fit / site] Mold weight, support and handling access
Raw supplier entry: [missing]
Source unit / basis: [missing]
Buyer-normalized entry: [pending]
Document / trial reference: [missing]
Completeness note: Raw value missing
Comparison basis: Installed mold mass, support condition, crane/fork access and changeover route.
Verification boundary: Supplier drawings are inputs, not a lift plan, foundation design or safe-work procedure.

[Injection] Shot capacity and usable shot basis
Raw supplier entry: [missing]
Source unit / basis: [missing]
Buyer-normalized entry: [pending]
Document / trial reference: [missing]
Completeness note: Raw value missing
Comparison basis: Keep original mass/volume, reference resin or density, screw diameter, cushion and buyer shot demand visible.
Verification boundary: A converted value is a comparison aid; confirm the configured injection unit with the actual resin, runner and mold trial.

[Injection] Injection speed, volume rate, pressure and fill evidence
Raw supplier entry: [missing]
Source unit / basis: [missing]
Buyer-normalized entry: [pending]
Document / trial reference: [missing]
Completeness note: Raw value missing
Comparison basis: Separate screw linear speed, volume flow, pressure definition, profile and measured fill time.
Verification boundary: Catalogue maxima and conversions do not prove simultaneous performance or acceptable part quality.

[Plasticizing] Plasticizing capacity and recovery window
Raw supplier entry: [missing]
Source unit / basis: [missing]
Buyer-normalized entry: [pending]
Document / trial reference: [missing]
Completeness note: Raw value missing
Comparison basis: Rate, reference resin/test condition, screw, shot demand, cooling window and residence constraint.
Verification boundary: Normalize the declared test basis, then verify recovery and melt quality with the project resin and cycle.

[Energy / boundary] Energy method, included loads and denominator
Raw supplier entry: [missing]
Source unit / basis: [missing]
Buyer-normalized entry: [pending]
Document / trial reference: [missing]
Completeness note: Raw value missing
Comparison basis: Name machine-related, product-related or complete-cell method; record configuration, loads, exclusions and denominator.
Verification boundary: Matching units do not create a matching boundary. Use comparable files or an agreed metered trial before costing.

[Interfaces / safety] Robot, peripheral, data and safety interfaces
Raw supplier entry: [missing]
Source unit / basis: [missing]
Buyer-normalized entry: [pending]
Document / trial reference: [missing]
Completeness note: Raw value missing
Comparison basis: Endpoints, connector/media, exact specification/version, signals/nodes, safety path, options and fault behavior.
Verification boundary: Verify both configured endpoints and the separate safety validation at FAT/SAT; a 'ready' label is not evidence.

[Utilities / auxiliaries] Power, cooling, air and auxiliary scope
Raw supplier entry: [missing]
Source unit / basis: [missing]
Buyer-normalized entry: [pending]
Document / trial reference: [missing]
Completeness note: Raw value missing
Comparison basis: Voltage/phase/frequency, connected and operating demand, water conditions, air, oil and included auxiliaries.
Verification boundary: Reconcile supplier utility schedules with the final cell, site capacity and installed configuration.

[Service / handover] Spares, files, training and support handover
Raw supplier entry: [missing]
Source unit / basis: [missing]
Buyer-normalized entry: [pending]
Document / trial reference: [missing]
Completeness note: Raw value missing
Comparison basis: Critical parts, drawings, software/backups, manuals, training, warranty, response route and exclusions.
Verification boundary: Record contractual scope and named evidence; do not infer stock, response time or geographic coverage.

[Trial / documents] Trial configuration and acceptance evidence
Raw supplier entry: [missing]
Source unit / basis: [missing]
Buyer-normalized entry: [pending]
Document / trial reference: [missing]
Completeness note: Raw value missing
Comparison basis: Machine/mold/resin configuration, stable condition, sample plan, output/quality record, deviations and closure owner.
Verification boundary: The comparison record supports review only; final fit depends on approved documents and agreed trial evidence.

=== Quote B ===
Quote / file reference: [not recorded]

[Scope / identity] Quoted machine and configured scope
Raw supplier entry: [missing]
Source unit / basis: [missing]
Buyer-normalized entry: [pending]
Document / trial reference: [missing]
Completeness note: Raw value missing
Comparison basis: Model, injection unit, screw, clamping unit, options, auxiliaries and quote revision.
Verification boundary: Match the commercial offer to the controlled configuration list and drawings.

[Mold fit] Clamp, platen and tie-bar fit
Raw supplier entry: [missing]
Source unit / basis: [missing]
Buyer-normalized entry: [pending]
Document / trial reference: [missing]
Completeness note: Raw value missing
Comparison basis: Buyer-required clamp basis plus usable tie-bar spacing and platen area in one unit system.
Verification boundary: Check the mold drawing, projected-area/pressure basis and configured machine drawing; do not infer fit from nominal tonnage alone.

[Mold fit] Mold thickness, daylight, opening and ejection
Raw supplier entry: [missing]
Source unit / basis: [missing]
Buyer-normalized entry: [pending]
Document / trial reference: [missing]
Completeness note: Raw value missing
Comparison basis: Minimum/maximum mold thickness, opening stroke, daylight, ejector stroke/force and core requirements.
Verification boundary: Verify the installed mold stack, motion sequence and access using controlled drawings and an agreed trial.

[Mold fit / site] Mold weight, support and handling access
Raw supplier entry: [missing]
Source unit / basis: [missing]
Buyer-normalized entry: [pending]
Document / trial reference: [missing]
Completeness note: Raw value missing
Comparison basis: Installed mold mass, support condition, crane/fork access and changeover route.
Verification boundary: Supplier drawings are inputs, not a lift plan, foundation design or safe-work procedure.

[Injection] Shot capacity and usable shot basis
Raw supplier entry: [missing]
Source unit / basis: [missing]
Buyer-normalized entry: [pending]
Document / trial reference: [missing]
Completeness note: Raw value missing
Comparison basis: Keep original mass/volume, reference resin or density, screw diameter, cushion and buyer shot demand visible.
Verification boundary: A converted value is a comparison aid; confirm the configured injection unit with the actual resin, runner and mold trial.

[Injection] Injection speed, volume rate, pressure and fill evidence
Raw supplier entry: [missing]
Source unit / basis: [missing]
Buyer-normalized entry: [pending]
Document / trial reference: [missing]
Completeness note: Raw value missing
Comparison basis: Separate screw linear speed, volume flow, pressure definition, profile and measured fill time.
Verification boundary: Catalogue maxima and conversions do not prove simultaneous performance or acceptable part quality.

[Plasticizing] Plasticizing capacity and recovery window
Raw supplier entry: [missing]
Source unit / basis: [missing]
Buyer-normalized entry: [pending]
Document / trial reference: [missing]
Completeness note: Raw value missing
Comparison basis: Rate, reference resin/test condition, screw, shot demand, cooling window and residence constraint.
Verification boundary: Normalize the declared test basis, then verify recovery and melt quality with the project resin and cycle.

[Energy / boundary] Energy method, included loads and denominator
Raw supplier entry: [missing]
Source unit / basis: [missing]
Buyer-normalized entry: [pending]
Document / trial reference: [missing]
Completeness note: Raw value missing
Comparison basis: Name machine-related, product-related or complete-cell method; record configuration, loads, exclusions and denominator.
Verification boundary: Matching units do not create a matching boundary. Use comparable files or an agreed metered trial before costing.

[Interfaces / safety] Robot, peripheral, data and safety interfaces
Raw supplier entry: [missing]
Source unit / basis: [missing]
Buyer-normalized entry: [pending]
Document / trial reference: [missing]
Completeness note: Raw value missing
Comparison basis: Endpoints, connector/media, exact specification/version, signals/nodes, safety path, options and fault behavior.
Verification boundary: Verify both configured endpoints and the separate safety validation at FAT/SAT; a 'ready' label is not evidence.

[Utilities / auxiliaries] Power, cooling, air and auxiliary scope
Raw supplier entry: [missing]
Source unit / basis: [missing]
Buyer-normalized entry: [pending]
Document / trial reference: [missing]
Completeness note: Raw value missing
Comparison basis: Voltage/phase/frequency, connected and operating demand, water conditions, air, oil and included auxiliaries.
Verification boundary: Reconcile supplier utility schedules with the final cell, site capacity and installed configuration.

[Service / handover] Spares, files, training and support handover
Raw supplier entry: [missing]
Source unit / basis: [missing]
Buyer-normalized entry: [pending]
Document / trial reference: [missing]
Completeness note: Raw value missing
Comparison basis: Critical parts, drawings, software/backups, manuals, training, warranty, response route and exclusions.
Verification boundary: Record contractual scope and named evidence; do not infer stock, response time or geographic coverage.

[Trial / documents] Trial configuration and acceptance evidence
Raw supplier entry: [missing]
Source unit / basis: [missing]
Buyer-normalized entry: [pending]
Document / trial reference: [missing]
Completeness note: Raw value missing
Comparison basis: Machine/mold/resin configuration, stable condition, sample plan, output/quality record, deviations and closure owner.
Verification boundary: The comparison record supports review only; final fit depends on approved documents and agreed trial evidence.